Product Detail: Offer 89LV51RD2 PHILIPS, 89LVJU, 89LPCFDH from Hong Components In Stock Suppliers in 【Price】【Datasheet PDF】USA. 89lv51rd2 datasheet datasheet, cross reference, circuit and application notes in pdf format. PHILIPS[Philips Semiconductors]. Part No. P89LV51RB2 P89LV51RB2BA P89LV51RB2BBC P89LV51RC2 P89LV51RC2BN P89LV51RC2FA.
|Published (Last):||8 April 2011|
|PDF File Size:||15.79 Mb|
|ePub File Size:||17.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Saving a macro 1. The data for Atlanta and Calgary are shown as in Figure 3b and Figure 3c. Images in the image folder at C: Opening a macro 1. Double-click on Flash Magic icon located at the desktop to launch the software.
HOW TO PROGRAMME THE MODULE BY USING FLASH MAGIC |
The contents of the macro file, testloop. All macro files users create have to be saved in this new project folder before downloading them to the hardware. At anytime when images get drag-and-drop into an animation tab, an equivalent read-only macro file is generated on the Macro File tab but can from the Animation Tab.
Further information is available at www. May 30, Page 6 of 12 Executing a macro Click on the Execute Macro button to download the content of the macro file to the hardware. It is divided into the following sections: All information contained in this document has been checked with the greatest care. Select a macro file, for example testloop. It’s a community-based project which helps to repair anything. Launch Window Explorer 2.
Macros File Tab Macro file consist of commands that allow users to: Refer to Figure 5. The data, time, and the locations of all the input files are displayed in this activity log field.
The Gamma Graph is the plot of gamma level from 1 to Double click the Setup. All images, which are bit bmp or jpg file format, can be stored in any directory on PC.
The project will be located at the C: Next, close up the connector as shown in Figure 11b.
P89LV51RD2 Datasheet(PDF) – NXP Semiconductors
Delay window allows users to select the delay period in second between images. Set interval delay between images if necessary. Macro files can be edited directly under this Macro Tab.
The preview animation tab allows users to preview animation. Image with no specific name is applicable for both. Ng Vic Tor, Hassrizal B. In our case, it should be assign to 89LV51RD2. Refer to Figure 4. PPJ project file, the software automatically creates a folder, which has the same name and stores the file directory: Images start with atlxxx is meant for Atlanta Display Module whereas images start with calxxx is meant for Calgary Module display.
Next, pull out the Calgary flex from the connector as shown in Figure 10b. If there is a massage popped up saying that the Baud Rate is too high, hen reduce the Baud Rate to How to Download the Hex File to the Microcontroller 1.
Figure 2a Figure 2b 3. The Figure 6 as shown below will be datasyeet.
【89LV51RD2 PHILIPS】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA
Calgary, x 64 2. At anytime, users can reopen any previously saved project by double-clicking on YourProject. Write pixel data to the display.
Select Transfer to Display to execute the gamma input file and send it to the display module. The process is shown in the Figure 2a.
HOW TO PROGRAMME THE MODULE BY USING FLASH MAGIC
However, downloading a free version of the Flash Magic software or any other compatible software from the link http: Atlanta, x 64 1. The typical value for Baud Rate is Automatically it would download the hex file to the IC until finished as the Figure 7b.
Use Macro tab to open, execute, edit, and save user generated macros. Navigate to the directory where the Osram Pictiva has been installed, or navigate to C: Upon delivery, the firmware has already been downloaded to the board.
Before clicking on the start button for programming, the flash has to be erased by selecting either Erase all Flash or Erase blocks used by Hex File if the address of that specific block is known. Next, remove the Reference Datazheet board by using hexagon key 2. The file requires the values for phase 1 and phase 2 followed by 8 bytes 15 levels of input from the user.